The Best Honeywell Miller G2 Connector

Easiest wire connector on the market

TICONN solder seal connectors will make your wire connection waterproof just in seconds;

also it applies mechanical damage protection and prevents wire corrosion!

Our connectors are an irreplaceable tool for fast, reliable and effective wire connection in any place and are appreciated by handymen all over the world!

Package Includes:

40 x White Connectors: Suits Cable/ Wire Sizes 0.25-0.34mm² (A.W.G:26-24);

50 x Red Connectors: Suits Cable/ Wire sizes 0.5-1.0mm² (A.W.G:22-18);

50 x Blue Connectors: Suits Cable/ Wire sizes 1.5-2.5mm² (A.W.G:16-14);

10 x Yellow Connectors: Suits Cable/ Wire sizes 4.0-6.0mm² (A.W.G:12-10)

HOW TO USE:

 1.Select the proper size connector for the wires, stripped wires.

 2.Insert the stripped wires into the connector.

 3.Apply heat evenly to the connector from the 2 ends first until tubing shrinks and the adhesive flows, then continuously apply heat evenly until solder sleeve melt and seal.

Note:

 1.For best result, please use a hot air gun and rotate the connector to evenly apply heat.

 2.Please raise the temperature from low to high gradually when you use the hot air gun to heat the wire connector.

 3.Please DO NOT set the high temperature at the beginning, or the surface of connector will be over-heated, which will lead to the tube melt while the solder ring still not melt.

 4.Keep the hot air gun at the proper distance. Don’t get too close.

Technical Specifications:

  Shrinkage ratio 2:1

  Minimum shrink temperature: 80°C

  Minimum temperature for solder to melt: 138°C

  Operating temperature :-55℃ – 125℃

  Waterproof Class: IP 67

Easiest wire connector on the market – TICONN 200 PCS Heat Shrink Butt Connectors

Whether you are working on your boat, vehicle, home or scientific projects, TICONN heat shrink butt connectors will ensure strong crimps, increased current flow and waterproof connections every time!

Features: 
Comply with all Relevant European Standards, Shrinkage Ratio: 3:1. 
Dual-walled: polyolefin tubing on the outside and hot melt adhesive in inside. 
Wire gauge imprint on connectors and color identification.
Ideal translucent provides tensile strength, allows visual inspection.
Allows visual inspection, prevents corrosion, and provided a waterproof seal.
Specification:
–Shrinkage ratio 3:1
–Minimum shrink temperature: 80°C
–Full recovery temperature: 130°C
–Operating temperature: from -55°C to 125°C

Note:

For best results, please choose the right connector, use a hot air gun, heat evenly until connector reduces in size and the adhesive flows, filling gaps within the terminals.

Package Includes:

90 x Red Connectors: Suits Cable/ Wire Sizes 0.5-1.0mm² (A.W.G:22-16);

90 x Blue Connectors: Suits cable/ wire sizes 1.5-2.5mm² (A.W.G:16-14);

20 x Yellow Connectors: Suits cable/ wire sizes 4.0-6.0mm² (A.W.G:12-10);

1 x PP Storage Case

Guarantee & Friendly Customer Service:
TICONN guarantees all buyers 100% satisfaction, once you find any problem of the product, please feel free to contact us, we will solve it as soon as we can.

100% Satisfaction Guarantees for risk-free shopping!

The Miller Turbo T-BAK Personal Fall Limiter is the first retractable designed to tie back anywhere along the lifeline, offering more tie-off anchorage locations with a greater variety of beam-size options. The all-in-one, self-retracting lifeline/anchorage connector design is both safer and more cost-effective than tie-back shock-absorbing lanyards. Safer because it eliminates tripping hazards and arrests free falls within inches. More cost-effective because it reduces the amount of equipment required to purchase and use on the job site, which in turn reduces the need for frequent gear changes. This saves time and increases productivity. The high-strength EXTREME webbing is abrasion-resistant and features white side stripe stitching to indicate it is specially designed for tie-back applications. Miller’s patented 5K locking snap hook is also purpose-designed for tie-back use, boasting a 5,000 lb (22 kN) gate load capacity from any angle. This ensures the hook will not fail if load forces are concentrated on the face or side of the hook. Various unit end connector options are available. Twin unit offerings include two options for 100% tie-off fall protection: the D-ring connector system, which connects directly to the safety harness back D-ring, and the G2 connector system. The G2 is the lightest twin connector available, and features a rotating webbing retainer clip to prevent the gate from opening. This tie-back PFL meets all applicable OSHA, ANSI, CSA and CE standards, including the ANSI Z359.14-2012 requirement that states only 24-inches (.61 m) or less of lifeline extends out of the housing when the unit is fully retracted.

It Can apply to the same series sockets and connectors;
Package Quantity:1pcs;
Model No: DKJ35-50;
Rated Current: 315amp;
Wire Section: 35-50mm2;

Size:9-Feet  |  Style:Lanyard Connector – Aluminum Locking Snap Hook The Miller Twin Turbo Fall Protection System with G2 Connector provides continuous 100% tie-off protection for a safer, better alternative to double-leg shock-absorbing lanyards. The Twin Turbo G2 Connector is extremely lightweight, which serves to reduce worker fatigue and increase productivity. The G2 Connector also features a webbing retainer clip that rotates freely to prevent unintentional opening of carabiner gate during a fall. For comfort, a D-pad clip is also included to keep the harness webbing and D-pad in place. The Miller Twin Turbo Fall Protection System reduces fall clearance requirements which makes it useful in more applications. It also affords workers more mobility: the PFLs swivel independently in multiple directions to optimize freedom of movement and prevent the webbing from twisting or binding to the unit. The self-retracting lifelines eliminate tripping hazards, and the increased mobility means more versatility and ultimately, more productivity. Lanyard end connector options include steel & aluminum locking snap hooks and steel & aluminum locking rebar hooks. Turbolite PFLs are available in 6-foot and 9-foot lengths. This personal fall arrest system meets all applicable OSHA, ANSI, and CSA requirements.